Publications by Staff

Dr T V Hanumantha Rao - (12)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Condition Monotoring and Detection of Unbalance Using Vibration Signature Analysis International Journal of Recent Scientific Research , Vol.6, Issue,8,pp.5796-5800.August,2015. International Journal Dr T V Hanumantha Rao Mechanical Engineering 2015-2016
2 Variable Compression Ration Diesel Engine Performance Analysis Engineering Technology Trends and Technology (IJETT), Number, 01, October 2015 International Journal Dr T V Hanumantha Rao Mechanical Engineering 2015-2016
3 Stress analysis of 4stroke diesel engine Piston 3rd International Conference on Progress In Production,Mechanical And Automobile Engineering(ICPMAE 2015) ISBN: 978-93-85225-02-4,1st February, 2015, International Conference Dr T V Hanumantha Rao Mechanical Engineering 2014-2015
4 A Parametric study on design of helmet to mitigate brain damage and to optimize the weight ARPN Journal of Engineering and Applied Sciences, Vol 10,NO.6,April 2015,ISSN1819-6608, International Journal Dr T V Hanumantha Rao Mechanical Engineering 2014-2015
5 A study on Design and Analysis of Hybrid Vibration Damper with Energy Harvesting and Optimal Damping Effect Springer - IE Journal Volume 95, Issue 2 pp 97-102 with DOI 10.100/s400-32-014-0115-3. International Dr T V Hanumantha Rao Mechanical Engineering 2013-2014
6 Diagnostic approach to Vibration Measurements in Dredger Propulsion system Journal of Institution of Engineers-vol -75 Jan2005 National Dr T V Hanumantha Rao Mechanical Engineering
7 Optimization of Transportation System in a division of Tribal Welfare Department of Andhra Pradesh Journal of Industrial Engineering- March 2005 National Dr T V Hanumantha Rao Mechanical Engineering
8 Fault Diagnosis of Harbor end Diesel Generator set in Dredger, a report on excessive vibration and its solution Journal of Institute of Naval Architects-March 2005. National Dr T V Hanumantha Rao Mechanical Engineering
9 An Approach to Apply Total Quality Management to the Engineering Education Processes The Indian Journal of Technical Education, IJTE-Volume 35 No:4 October 2012 National Dr T V Hanumantha Rao Mechanical Engineering
10 A Study on Coupled and modified structure analysis for effective modal testing International Journal of Mechanical Engineering and Research (IJMER Vol -1, Number 2 (2011) PP 275-282 International Dr T V Hanumantha Rao Mechanical Engineering
11 A Study on Damper Health Diagnosis in Marine Diesel Engine using Condition Monitoring Techniques Journal of Mechanical Engineering and Research Vol -1, Number 2 (2011) PP 345-353 National Dr T V Hanumantha Rao Mechanical Engineering
12 A Generic Approach to Apply TQM to the Engineering Education Process International Journal of Educational Administration Volume 4, Number 1, pp 31-37 -Jan 2012 International Dr T V Hanumantha Rao Mechanical Engineering


Dr.B. Naga Raju- (20)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Effect of Cutting Parameters on Drilling to Optimize MRR and Temperature by Response Surface Methodology under Dry Condition International Journal of Engineering Trends and Technology (IJETT), Volume-47 Number-1, May -2017. International Journal B.Naga Raju Mechanical Engineering 2017-2018
2 Studies on Tribological properties of SiC and Fly Ash reinforced glass fiber epoxy composites International Journal of Mechanical Engineering &Technology (IJMET), Volume 7, Issue 6, November-December 2016,pp.199-208 International Journal B.Naga Raju Mechanical Engineering 2017-2018
3 Effect of pitch angle on Bending Stresses of Bevel Gears International Advaced Research Journal in Science, Engineering and Technology (IARJSET) – Volume 3, Issue 11, November 2016 International Journal B.Naga Raju Mechanical Engineering 2016-2017
4 Experimental Investigation on Tensile and Damping Properties of Flyash Reinforced Glass Fibre Epoxy Composites International Advanced Research Journal in Science, Engineering and Technology (IARJSET) – Volume 3, Issue 9, September 2015 International Journal B.Naga Raju Mechanical Engineering 2015-2016
5 Quasi-Dynamic Stress Analysis on Crank Shaft of Computerized Variable Compression Ratio (VCR) Diesel International Journal of Engineering Trends and Technology (IJETT) – Volume 30, Number 4, Dec 2015 International Journal B.Naga Raju Mechanical Engineering 2017-2018
6 Modelling and Thermal-Static Coupled Field Analysis of Ventilated Disc Brake International Journal of Engineering Trends and Technology (IJETT) – Volume 30, Number 4, Dec 2015. International Journal B.Naga Raju Mechanical Engineering 2015-2016
7 Study of Influence of process parameters on surface roughness of AMMCS in wire electrical Discharge Machine 4th IC on Materials processing and Characterization organized by GRIET, Hyderabad, March 14th-15th, 2015 and published in the Elsevier, International Conference B.Naga Raju Mechanical Engineering 2014-2015
8 Stress Analysis of Crane Hook Using Fea 3rd International conference o Progress, Mechanical and Automobile Engineering, (ICMAE-2015), Goa, Feb 1st 2015 International Conference B.Naga Raju Mechanical Engineering 2014-2015
9 Study of Influence of process parameters on surface roughness of AMMCS in wire electrical Discharge Machine ARPN Journal of Engineering and Applied Sciences, Vol. 10, No.4, March 2015. International Journal B.Naga Raju Mechanical Engineering 2014-2015
10 Stress Analysis of Crane Hook Using Fea international journal of current engineering and scientific research (ijcesr), ISSN (print): 2393-8374, volume-2, issue-2, 2015. International Journal B.Naga Raju Mechanical Engineering 2014-2015
11 Design and Fabrication of Mechatro Hand International Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-102-108 International Journal B.Naga Raju Mechanical Engineering 2015-2016
12 Finite Elements Analysis of Solid and Ventilated Disc Brake International Journal of Science and Research (IJSR), ISSN (online) :2319-7064 International Journal B.Naga Raju Mechanical Engineering 2014-2015
13 Evaluation of aMaterial Removal Rate and Surface Roughness in Turning Using Response Surface Methodology. Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-772-779 ISSN-2250-1758 International Journal B.Naga Raju Mechanical Engineering 2014-2015
14 Optimization of Machining Parameters for Cutting AMMC’s on Wire Cut EDM using RSM International Jouranl of Enigneering Trends and Technology (IJETT), Volume23 Number 2-May 2015,ISSN-2231-5381 International Journal B.Naga Raju Mechanical Engineering 2014-2015
15 Optimization of tool Temprature and Roughness in wet and dry Condition During Turning of Mid Steel Using Resopnse Surface Method International Jouranl of Enigneering Trends and Technology (IJETT), ISSN:2278-9359 Volume-4,Issue-5 International Journal B.Naga Raju Mechanical Engineering 2014-2015
16 Static and Thermal analysis of disc brake with Brake pad International Journal of Engineering Trends and Technology (IJETT), Volume 23 Number 8-May 2015 International Journal B.Naga Raju Mechanical Engineering 2014-2015
17 Finite Elements Analysis of Solid and Ventilated Disc Brake International Journal of Science and Research (IJSR), ISSN (online) :2319-7064 Year 2014 National Conference B.Naga Raju Mechanical Engineering 2014-2015
18 Studies on Tribological properties of ZnO filled polymer Nano-composites ARPN journal of Engineering and applied sciences, Vol-6, no-6, June 2011 International B.Naga Raju Mechanical Engineering
19 Synthesis and characterization of high pure ZnO nano particles by combustion route” in International conference on “Nano Technology Materials & composites for frontier applications” NANOCON 2010, conducted by Bharatiya vidhya peeth university, PUNE, INDIA on cot 14th & 15th 2010. Conference International B.Naga Raju Mechanical Engineering 2010-2011
20 Synthesis and characterization of high pure ZnO nano particles by conventional methods” in International journal of Nanotechnologyand its Applications, vol 4,number3(2010),pp.199-205. Journal International B.Naga Raju Mechanical Engineering 2010-2011


Dr.N. Indra Kiran- (16)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Benchmarking the industry National Seminar on Vehicle Dynamics held at Andhra University during Feb 2003 National Conference Dr.N. Indra Kiran Mechanical Engineering 2002-2003
2 Pattern identification in statistical process control using Artificial Neural Networks Vardhaman College of engineering, Hyderabad during, August 6-7, 2010. National Conference Dr.N. Indra Kiran Mechanical Engineering 2010-2011
3 To incorporate best practices in an organization International Conference on Modeling, Simulation and Manufacturing Systems held at PSG College of technology, Coimbatore, in July 2004. International Conference Dr.N. Indra Kiran Mechanical Engineering 2004-2005
4 Performance evaluation of a manufacturer using six sigma methodology International Conference on Modeling, Simulation and Manufacturing Systems held at Andhra University, in June 2008. International Conference Dr.N. Indra Kiran Mechanical Engineering 2008-2009
5 A Study on Selection Issues of an Integrated Service Provider/4PL Using AHP INCRAME 2011 conducted by MGR University during April 21-22, 2011. International Conference Dr.N. Indra Kiran Mechanical Engineering 2010-2011
6 A Three Level Hierarchal Framework for Minimization of Costs in Process Industry-A Case Study in an Integrated Steel plant INCRAME 2011 conducted by MGR University during April 21-22, 2011. International Conference Dr.N. Indra Kiran Mechanical Engineering 2010-2011
7 Effective Control Chart Pattern Recognition Using Artificial Neural Networks International Journal of Computer Science and Network Security, March 2010, Vol.10, No.3, pp.194-199. International Journal Dr.N. Indra Kiran Mechanical Engineering 2009-2010
8 Training Multilayered Perceptrons for Pattern Recognition: A Comparative Study of Three Training Algorithms International Journal of Information Technology and Knowledge Management, July-Dec 2010, Vol. 2, No. 2, pp. 579-584. International Journal Dr.N. Indra Kiran Mechanical Engineering 2010-2011
9 Control Chart Pattern Recognition Using Artificial Neural Networks and Statistical Features International journal of artificial intelligence and computational research , July-Dec 2010, Vol 2, No.2, pp.73-79. International Journal Dr.N. Indra Kiran Mechanical Engineering 2016-2017
10 Effective Control Chart Pattern Recognition Using Artificial Neural Networks and Statistical Features International J.of Multidispl.Research & Advcs. In Engg, July 2010, Vol.2, No. 2, pp.347-361. International Journal Dr.N. Indra Kiran Mechanical Engineering 2010-2011
11 Feature Based Control Chart Pattern Recognition Using Artificial Neural Networks International Journal of computer Applications in Engineering Technology and Sciences, April 10 – Sept 10, Vol. 2, No.2, pp.485-491. International Journal Dr.N. Indra Kiran Mechanical Engineering 2010-2011
12 A Study on Selection Issues of an Integrated Service Provider The journal of industrial safety engineering Vol 2 No 1 , March, 2015. International Journal Dr.N. Indra Kiran Mechanical Engineering 2014-2015
13 Back Propagation Neural Networks for the Analysis of Control Chart Pattern Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-602-605 International Journal Dr.N. Indra Kiran Mechanical Engineering 2014-2015
14 Effect of Cutting Parameters in Turning of Aluminium 2024 to Obtain Maximum MRR and Minimum Temprature by using RSM (Under Dry Condition) Interanational Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-94-101 International Journal Dr.N. Indra Kiran Mechanical Engineering 2015-2016
15 Training Multi layer perceptions for pattern recognition “ A comprehensive study of Five Trans Algorithms \" International Conference of Artificial Intelligence and its Applications in Hongkong International Conference Dr.N. Indra Kiran Mechanical Engineering 2010-2011
16 Back propagation ANN for the analysis of control chart patternť at AIMTDR 2010 conducted by Andhra University, Visakhapatnam during December 13th to 15th 2010 Conference International Dr.N. Indra Kiran Mechanical Engineering 2010-2011


Dr.K.Siva Prasad- (87)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Review on Design of Rolling Process J Advanced Research in Manufacturing Material Science & Metallurgy, Engineering,2017; Volume.4, Issue. 1&2,pp. 9-19. International Journal Dr.K.Siva Prasad Mechanical Engineering 2017-2018
2 Study on Stress Analysis of Araldite HY-951 and CY-230 Bell Crank Lever using Photoelasticity and FEM Journal of Automobile Engineering and Applications, Volume 4, Issue 2,pp.10-21. International Journal Dr.K.Siva Prasad Mechanical Engineering 2017-2018
3 Investigation of stresses in U-shaped metal bellow using EJMA standards International Journal of Advanced Design and Manufacturing Technology, Volume.11, Issue.2, 2017,pp.25-35. International Journal Dr.K.Siva Prasad Mechanical Engineering 2017-2018
4 Effect of Pulsed Current Micro Plasma Arc parameters on weld bead geometry of AISI 316Ti Austenitic Stainless Steel Journal of Mechanical and Mechanics Engineering ,Volume 3 Issue 1,2017,pp.56-65. International Journal Dr.K.Siva Prasad Mechanical Engineering 2016-2017
5 Investigation on weld bead geometry of pulsed current micro plasma arc welded AISI 316Ti austentic stainlees steel Proceedings of 6th International & 27th All India Manufacturing Technology Design and Resaerch Conference (AIMTDR-2016) held at college of Enginering, Pune during 16-18 th December 2016, pp.1603-1606. International Conference Dr.K.Siva Prasad Mechanical Engineering 2016-2017
6 Investigation on pitting corrosion rate of pulsed current micro plasma arc welded AISI 321 austentic stainless steel Proceedings of 6 th International & 27 th All India Manufacturing Technology Design and Resaerch Conference (AIMTDR-2016) held at college of Enginering, Pune during 16-18 th December 2016, pp.1381-1385. International Conference Dr.K.Siva Prasad Mechanical Engineering 2016-2017
7 Investigation on Pitting Corrosion Rate of Pulsed Current Micro Plasma Arc Welded AISI 316Ti Austenitic Stainless Steel 5th Global Conference on Materials Science and Engineering  CMSE 2016, held at Tunghai University,Taiwan during 8 th -10 th November 2016. International Conference Dr.K.Siva Prasad Mechanical Engineering 2016-2017
8 Experimental Investigation on Tensile and Damping Properties of SiC and Flyash Reinforced Glass Fiber Epoxy Composites Journal of Recent Trends in Mechanics,2016, Volume 1, Issue 3,pp.10-19. International Journal Dr.K.Siva Prasad Mechanical Engineering 2016-2017
9 Effect of Pulse Current Micro Plasma Arc Welding Parameters on Pitting Corrosion Rate of AISI 316Ti Sheets in 3.5 N NaCl Medium Journal of Materials & Metallurgical Engineering, 2016, Volume 6, Issue 3, pp.12-24. International Journal Dr.K.Siva Prasad Mechanical Engineering 2016-2017
10 Design and Analysis of Helical Gear with Involute Profile Journal of Advancement in Machines, Volume 1, Issue 3,2016, pp.1-21. International Journal Dr.K.Siva Prasad Mechanical Engineering 2016-2017
11 Fatigue Analysis of Friction Welded Stringer Panel of an Aircraft Wing Journal of Automation and Automobile Engineering ,Volume 1 ,Issue 3, 2106, pp-1- 21. International Journal Dr.K.Siva Prasad Mechanical Engineering 2016-2017
12 Review on Corrosion of welded Joints Journal of Materials & Maraullurgical Engineeiring Volume 5, Issue 3 ISSN:2231-3818(online) ISSN:.2321-4236(print) International Journal Dr.K.Siva Prasad Mechanical Engineering 2015-2016
13 Effect of Helix Angle on Performance of Helical Gear for Marine Applications Trends in Machine Design www.stmjournals.com, Volume 2, Issue 3 International Journal Dr.K.Siva Prasad Mechanical Engineering 2015-2016
14 Review on Application of Utility Poles for Power Transmission Journal of Materials & Metallurgical Engineering, Volume 6, Issue 1, 2016, pp.1-11. International Journal Dr.K.Siva Prasad Mechanical Engineering 2015-2016
15 Review on Metal Bellows Used in Expansion Joints Journal of Advancements in Robotics, Volume 3, Issue 1, 2016,pp.1-12. International Journal Dr.K.Siva Prasad Mechanical Engineering 2015-2016
16 Study of factors effecting surface roughness and tool tip temperature in step turning using factorial technique Journal of Manufacturing Scince Production, Volume 15, Issue.4,2015,pp.319-326. International Journal Dr.K.Siva Prasad Mechanical Engineering 2015-2016
17 Study on Effect of Plain Milling Parameters on Cutting Forces and Surface Finish Using Statistical Approach Journal of Advances in Mechanical Engineering and Technology, Volume 1, Issue 1,(2015), pp. 22-34 International Journal Dr.K.Siva Prasad Mechanical Engineering 2015-2016
18 Review on Corrosion of Austenitic Stainless Steels in Chloride Medium Journal of Advanced Research in Manufacturing, Material Science & Metallurgical Engineering, Vol. 2, No.2, (2015), pp.1-5. International Journal Dr.K.Siva Prasad Mechanical Engineering 2015-2016
19 Experimental Investigation on 4-stroke Diesel Engine using waste cooking oil biodiesel fuel Journal of Automobile Engineering and Application, Volume.2, Issue.2, 2015,pp.19-28 International Journal Dr.K.Siva Prasad Mechanical Engineering 2015-2016
20 Static Analysis of 4-Blade Marine Propeller, Journal of Aerospace Engineering & Technology, 2015,Volume 5, Issue 2, pp. 8-21. International Journal Dr.K.Siva Prasad Mechanical Engineering 2015-2016
21 Study on Weld Quality Characteristics of Micro Plasma Arc Welded Austenitic Stainless Steels Procedia Engineering (Elsevier), Volume.97 National Conference Dr.K.Siva Prasad Mechanical Engineering 2014-2015
22 Application of Grey Relational Analysis for Optimizing Weld pool geometry parameters of Pulsed Current Micro Plasma Arc Welded Inconel 625 sheets International Journal of Advanced Manufacturing Technology (SPRINGER) International Journal Dr.K.Siva Prasad Mechanical Engineering 2014-2015
23 Study of Factors Effecting Green Compression Strength and Shear Strength of Molding Sand using Factorial Technique International Journal of Production Engineering, Vol.1.:Issue 1 IJPE(2015)9-20 Journalspub-2015 International Journal Dr.K.Siva Prasad Mechanical Engineering 2014-2015
24 Statistical Analysis of Factors Effecting Surface Finish in Plain Milling International Journal of Production Engineering, Vol.1.:Issue 1 IJPE(2015)1-8 Journalspub-2015 International Journal Dr.K.Siva Prasad Mechanical Engineering 2014-2015
25 Investigation on effect of pulsed current MPAW parameters on weld quality characteristics at various thicknesses of AISI 304L Sheets 3rd Global Conference on Materials Science and Engineering (CMSE 2014) held at Shanghai, China during 20th to 23rd October 2014. International Conference Dr.K.Siva Prasad Mechanical Engineering 2014-2015
26 Optimizing Die Corner Radius of Deep Drawing Die International Journal of Trends in Mechanical Engineering & Technology, Volume 4, Issue 2, (2014),pp. 22-32 International Journal Dr.K.Siva Prasad Mechanical Engineering 2014-2015
27 Multi-objective Optimization of Weld Bead Geometry Parameters of Pulsed Current Micro Plasma Arc Welded AISI 304L Stainless Steel Sheets Using Enhanced Non-dominated Sorting Genetic Algorithm J. Manuf. Sci. Prod. 2014, 14(2): 79 – 85. International Journal Dr.K.Siva Prasad Mechanical Engineering 2014-2015
28 Investigation on effect of pulsed current MPAW parameters on weld quality characteristics at various thicknesses of AISI 304L Sheets Proceedings of CMSE 2014, Shanghai, Chinba,Oct.20 - 23, 2014, pp.76-86. International Dr.K.Siva Prasad Mechanical Engineering 2014-2015
29 Study on effect of die corner radius in deep drawing process Pyrex Journal of Engineering and Manufacturing Technology, Vol.1(1), pp.011-016 November, 2014 International Journal Dr.K.Siva Prasad Mechanical Engineering 2014-2015
30 Optimizing pulsed current Micro Plasma Arc Welding parameters to maximize Ultimate Tensile strength of AISI 304L sheets using Response Surface Method Applied Mechanics and Materials, Volume.660 (2014), pp. 322-326. International Dr.K.Siva Prasad Mechanical Engineering 2013-2014
31 Multi-objective Optimization of Weld Bead Geometry Parameters of Pulsed Current Micro Plasma Arc Welded AISI 304L Stainless Steel Sheets Using Enhanced Non-dominated Sorting Genetic Algorithm J. Manuf. Sci. Prod. 2014, 14(2): 79 – 85. International Journal Dr.K.Siva Prasad Mechanical Engineering 2014-2015
32 Optimization of Fusion Zone Grain Size, Hardness, and Ultimate Tensile Strength of Pulsed Current Micro plasma Arc Welded AISI 304L Sheets Using Genetic Algorithm Hindawi Publishing Corporation International Journal of Manufacturing Engineering, Volume 2014, Article ID 943643, 8 pages International Dr.K.Siva Prasad Mechanical Engineering 2014-2015
33 A Review on Welding of AISI 304L Austenitic Stainless Steel Journal of Manufacturing Science & Production, Volume.14,Issue.1, pp.1-11. International Journal Dr.K.Siva Prasad Mechanical Engineering 2014-2015
34 Critical Review of Fatigue Properties of Friction Stir Welds of Aluminum Alloys Journal of Materials and Metallurgical Engineering, Volume.4, Issue.1,2014,pp.1-6. International Journal Dr.K.Siva Prasad Mechanical Engineering 2014-2015
35 Optimization of Fusion Zone Grain Size, Hardness and Ultimate Tensile Strength of Pulsed Current Microplasma Arc Welded AISI 304L Sheets Using Genetic Algorithm International Journal of Manufacturing Engineering, Volume 2014, Article ID.943643, 8 pages, http://dx.doi.org/10.1155/2014/943643. International Dr.K.Siva Prasad Mechanical Engineering 2014-2015
36 Effect of welding current mode on weld quality characteristics of pulsed current micro plasma arc welded AISI 304L sheets Applied Mechanics and Materials, Vols. 465-466 ,2014, pp. 1209-1213. International Dr.K.Siva Prasad Mechanical Engineering 2014-2015
37 Study on effect of welding current mode on weld quality characteristics of AISI 304L sheets 4th International Conference on Mechanical and Manufacturing Engineering (ICME 2013) held at Kuala Lampur, Malaysia on 17th & 18th December 2013. International Dr.K.Siva Prasad Mechanical Engineering 2013-2014
38 Aerofoil Profile Analysis and Design Opimisation Journal of Aerospace Engineering and Technology Volume 3, Issue.2, 2013, pp.1-10. International Dr.K.Siva Prasad Mechanical Engineering 2012-2013
39 An Investigation on Effect of Welding Current Mode on Weld Quality Characteristics of Microplasma Arc Welding of Inconel 625 Sheets Journal of Materials & Metallurgical Engineering, Vol.3,Issue.1,2013, pp.2231-3818. International Dr.K.Siva Prasad Mechanical Engineering
40 Effect of welding parameters on pitting corrosion rate of Pulsed Current Micro Plasma Arc Welded AISI 304L sheets in 1N HCl medium Journal of computational and applied research in engineering, Vol.3,No.1,2013,pp.1-11. International Dr.K.Siva Prasad Mechanical Engineering
41 Optimization of pulsed current parameters to minimize pitting corrosion in Pulsed Current Micro Plasma Arc Welded AISI 304L sheets using Genetic Algorithm International Journal of Lean Thinking, Voulme.4,Number.1,2013,pp.9-19. International Dr.K.Siva Prasad Mechanical Engineering
42 Study of Weld Quality Characteristics of Inconel 625 Sheets at Different Modes of Current in Micro Plasma Arc Welding Process, Research and Reviews Journal of Material Sciences,Volume.1, Issue.1,pp.20-27. National Dr.K.Siva Prasad Mechanical Engineering
43 Application of Grey Relational Analysis for Optimizing Weld pool geometry parameters of Pulsed Current Micro Plasma Arc Welded AISI 304L stainless steel sheets International Journal of Advanced Design and Manufacturing Technology , Volume.6, No.1, 2013,pp.79-86. International Dr.K.Siva Prasad Mechanical Engineering
44 Effect of welding parameters on pitting corrosion rate in 3.5N Nacl of Pulsed Current Micro Plasma Arc Welded AISI 304L sheets Journal of Manufacturing science and production, Volume.13,Issue-1-2,2013,pp.15-23. National Dr.K.Siva Prasad Mechanical Engineering
45 Multi Objective optimization of weld bead geometry parameters of Pulsed Current Micro Plasma Arc Welded Inconel 625 sheets using Enhanced Non-dominated Sorting Genetic Algorithm Journal of Materials & Metallurgical Engineering, Vol.3,Issue.1,2013, pp.2231-3818. International Dr.K.Siva Prasad Mechanical Engineering
46 Review on application of Taguchi method based Design of Experiments to Welding processes International Journal of Technology and Management, Vol.2, No.1,2013,pp.1-8. International Dr.K.Siva Prasad Mechanical Engineering
47 Study on effect of welding speed on micro structure and mechanical properties of pulsed current micro plasma arc welded Income 625 Sheets The Journal of Minerals and Materials Characterization and Engineering, Volume 11,Issue 10, 2012,pp.1027-1033. National Dr.K.Siva Prasad Mechanical Engineering
48 Optimizing fusion zone grain size and hardness of pulsed current micro plasma arc welded Inconel 625 sheets using Hooke & Jeeves Algorithm Journal of Multidiscipline Modeling in Materials & Structures, Volume 8, Issue 3, 2012),pp.338-354. National Dr.K.Siva Prasad Mechanical Engineering
49 Optimizing fusion zone grain size and hardness of pulsed current micro plasma arc welded SS304L sheets using Hooke & Jeeves Algorithm The Journal of Minerals and Materials Characterization and Engineering, Volume11,Issue 9, 2012, pp. 869-875. National Dr.K.Siva Prasad Mechanical Engineering
50 Effect of Process Parameters of Pulsed Current Micro Plasma Arc Welding on Weld Pool Geometry of AISI 304L Stainless Steel Sheets Journal of Materials & Metallurgical Engineering Volume 2, Issue 1, 2012, pp. 37-48. International Journal Dr.K.Siva Prasad Mechanical Engineering
51 Advances in Plasma Arc Welding : A Review Journal of Mechanical Engineering and Technology, Volume 4,Issue1,2012,pp.35-59 National Dr.K.Siva Prasad Mechanical Engineering
52 Optimizing pitting corrosion in 3.5 N NaCl medium of Pulsed Current Micro Plasma Arc Welded AISI 304L sheets using Genetic Algorithm Journal of Materials & Metallurgical Engineering, Volume 2, Issue 3, 2012, pp.39-49. International Journal Dr.K.Siva Prasad Mechanical Engineering
53 Study on effect of welding speed on micro structure and mechanical properties of pulsed current micro plasma arc welded AISI 304L Sheets Journal of Manufacturing science and production, Volume 12, Issue 2,2012,pp.95-103. International Journal Dr.K.Siva Prasad Mechanical Engineering
54 Study on factors effecting Weld Pool Geometry of Pulsed Current Micro Plasma Arc Welded SS 304L Austenitic Stainless Steel using Statistical Approach The Journal of Minerals and Materials Characterization and Engineering, Volume 12, Issue 8,2012,pp.790-799. National Dr.K.Siva Prasad Mechanical Engineering
55 Effect of pulsed current micro plasma arc welding process parameters on fusion zone grain size and ultimate tensile strength of SS304L sheets International Journal of Lean Thinking, Volume 3, Issue.1,2012,pp.107-118. International Dr.K.Siva Prasad Mechanical Engineering
56 Review on application of Response Surface Method based Design of Experiments to Welding processes Journal of Manufacturing Science & Production (De Gruyter), Volume12,Issue.1,2012,PP.17-24. International Dr.K.Siva Prasad Mechanical Engineering
57 Effect of process parameters of pulsed current micro plasma arc welding on weld pool geometry of Inconel 625 welds Kovove Materialy - Metallic Materials, Volume 50,No.3, (2012),PP.153-159. International Dr.K.Siva Prasad Mechanical Engineering
58 Effect of pulsed current micro plasma arc welding process parameters on fusion zone grain size and ultimate tensile strength of Inconel 625 sheets Acta Metallurgica Sinica (English letters), Volume 25,Number 3, (2012),pp.179-189. International Dr.K.Siva Prasad Mechanical Engineering
59 Application of Hooke & Jeeves method to optimize Ultimate Tensile Strength of Pulsed Current Micro Plasma Arc Welded Inconel 625 Nickel alloy International Journal of Lean Thinking,Volume 3, Issue.1, 2012,pp.42-52. International Dr.K.Siva Prasad Mechanical Engineering
60 Study on weld quality characteristics of pulsed current micro plasma arc welding of Inconel625 sheets The Journal of Minerals and Materials Characterization and Engineering, Volume.11,No.2,2012,pp.133-141. National Dr.K.Siva Prasad Mechanical Engineering
61 Optimization of Fusion Zone Grain Size, Hardness and Ultimate Tensile Strength of Pulsed Current Micro Plasma Arc Welded Inconel 625 Sheets Using Genetic Algorithm Journal of Manufacturing science and production, Volume 17, No.1, (2012), PP 31-41. International Dr.K.Siva Prasad Mechanical Engineering
62 Comparison of weld quality characteristics of SS304L and Inconel625 in Micro plasma arc welding process Journal of Manufacturing Technology Research, Volume4, Issue 3-4,(2012),PP 133-144. International Dr.K.Siva Prasad Mechanical Engineering
63 An investigation on weld quality characteristics of pulsed current micro plasma arc welded austenitic stainless steels International Journal of Engineering, Science and Technology (IJEST) MULTICRAFT, Volume 4, Issue 2,(2012),PP 159-168 International Dr.K.Siva Prasad Mechanical Engineering
64 Effect of welding speed on weld quality characteristics of pulsed current micro plasma arc welded AISI 304L Sheets Asian International Journal of Science and Technology in Production and Manufacturing Engineering, Volume 5, Number 4, (2012), PP 21-28. International Dr.K.Siva Prasad Mechanical Engineering
65 Study of Pulsed Micro Plasma Arc welding parameters on Weld Bead Geometry of AISI 304L Sheets using Factorial Method Thammasat International Journal of Science and Technology, Volume 17, Issue.1, 2012, pp.31-41. International Dr.K.Siva Prasad Mechanical Engineering
66 Effect of welding current mode on weld quality characteristics of Micro Plasma Arc Welded Inconel 625 weldsat AIMTDR 2012 held during 14-16 December 2012, at Jadhavpur University, Kolkata, India. International Dr.K.Siva Prasad Mechanical Engineering
67 Effect of welding speed on weld quality characteristics of pulsed current micro plasma arc welded AISI 304L Sheets 11th Global Congress on Manufacturing and Management GCMM 2012 held during 28-30 November 2012, at AUT University, Auckland, New Zealand. International Dr.K.Siva Prasad Mechanical Engineering
68 Prediction of weld pool geometry in pulsed current micro plasma arc welding of SS 304 L sheets ITJEMAST, Vol-2, Number 3, PP 325-336 International Dr.K.Siva Prasad Mechanical Engineering
69 Prediction of weld quality in plasma arc welding using statistical approach AIJSTPME , Vol-3, Number 4, PP 1-7 International Dr.K.Siva Prasad Mechanical Engineering
70 Prediction of Weld bead Geometry in Plasma Arc welding using factorial design approach International Journal of Minerals and Materials Characterization Engineering ( JMMCE), Vol-10,No 10 PP 875-886 {Impact factor 0 .32} International Dr.K.Siva Prasad Mechanical Engineering
71 A study on weld quality characteristics of pulsed current Micro Plasma Arc Welding of SS 304 L sheets Intl. Transaction Journal of Management & Applied sciences & Technologies, Vol 2, No- 4 PP 437 -446 ITJEMEST International Dr.K.Siva Prasad Mechanical Engineering
72 Optimisation of Surface Finish in End Milling using Response Surface Method National Conference NCSAME-2009 conducted by JNTU College of Engineering, Hyderabad, 20 – 21 August 2009 National Dr.K.Siva Prasad Mechanical Engineering
73 Compact Plate Fin Heat Exchangers (Aerospace Application) International Technical Seminar conducted by Fluid Power Society of India (FPSI) at Bangalore International Exhibition Centre, Bangalore, 10-12 December 2008. National Dr.K.Siva Prasad Mechanical Engineering 2008-2009
74 Optimistaion of surface finish of step turning using Surface Response Technique National Conference CAMED-2008 conducted by Gandhi Institute of Engineering and Technology (GIET), Gunupur, Orissa, 8-9 November 2008 National Dr.K.Siva Prasad Mechanical Engineering
75 Unconstrained Optimization for Maximizing Ultimate Tensile Strength of Pulsed Current Micro Plasma Arc Welded Inconel 625 sheets Proceedings of the InConINDIA 2012, AISC 132, Springer-Verlag Berlin Heidelberg 2012, pp.245-352 International Dr.K.Siva Prasad Mechanical Engineering
76 Optimizing Fusion Zone Grain Size And Ultimate Tensile Strength Of Pulsed Current Micro Plasma Arc Welding Welded SS304L Sheets Using Hooke & Jeeves Algorithm Proceedings of International Conference on Futuristic Trends in Materials and Energy Systems,V R Siddhartha Engineering College, Vijayawada, A.P., India, 29-30 December, 2011, pp. 112-119. International Dr.K.Siva Prasad Mechanical Engineering
77 Prediction of Pulsed Current Micro Plasma Arc Welding Process Parameters to obtain Sound Weld Pool Geometry in SS304L Stainless Steel Sheets INCRAME 2011, MGR University, Chennai, India, April 21-23, 2011. International Dr.K.Siva Prasad Mechanical Engineering
78 Prediction of Weld Quality in Plasma Arc Welding using Statistical Approach Proceedings of GCMM 2010, King Mongkut’s University of Technology, Bangkok, Thailand, Nov 22-24, 2010, pp.296-301 International Dr.K.Siva Prasad Mechanical Engineering
79 Compact Plate Fin Heat Exchangers (Aerospace Application) Fluid Power Society of India (FPSI) journal, Volume 53, Dec 2008 edition. National Dr.K.Siva Prasad Mechanical Engineering
80 Optimizing Fusion Zone Grain Size and Ultimate Tensile Strength of Pulsed Current Micro Plasma Arc Welded Inconel 625 Alloy Sheets using Hooke & Jeeves Method International Transaction Journal of Engineering, Management & Applied Sciences & Technologies. Volume 3 No.1, 2012,pp.87-100. International Dr.K.Siva Prasad Mechanical Engineering
81 Establishing Empirical Relations to Predict Grain Size and Hardness of Pulsed Current Micro Plasma Arc Welded SS 304L Sheets American Transactions on Engineering & Applied Sciences. Volume 1, No.1, 2012, pp.57-74. International Dr.K.Siva Prasad Mechanical Engineering
82 Establishing Empirical Relationships to Predict Grain Size and Hardness of Pulsed Current Micro plasma Arc Welded Inconel 625 Sheets Journal of Materials & Metallurgical Engineering Volume 1, Issue 3, 2011, pp.1-10 International Dr.K.Siva Prasad Mechanical Engineering
83 Prediction of Weld Bead Geometry in Plasma Arc Welding using Factorial Design Approach Journal of Minerals & Materials Characterization & Engineering, Volume 10, No.10, pp.875-886. International Dr.K.Siva Prasad Mechanical Engineering
84 A Study on Weld Quality Characteristics of Pulsed Current Micro Plasma Arc Welding of SS304L Sheets International Transaction Journal of Engineering, Management & Applied Sciences & Technologies. Volume 2, No.4, 2011, pp.437-446. International Dr.K.Siva Prasad Mechanical Engineering
85 Prediction of Weld Pool Geometry in Pulsed Current Micro Plasma Arc Welding of SS304L Stainless Steel Sheets International Transaction Journal of Engineering, Management & Applied Sciences & Technologies. Volume 2, No.3, 2011, pp.325-336. International Dr.K.Siva Prasad Mechanical Engineering
86 Optimizing pulsed current micro plasma arc welding parameters to maximize ultimate tensile strength of Inconel625 Nickel alloy using response surface method International Journal of Engineering, Science and Technology, Volume. 3, No. 6, 2011, pp. 226-236. International Dr.K.Siva Prasad Mechanical Engineering 2011-2012
87 Prediction of Weld Quality in Plasma Arc Welding using Statistical Approach Asian International Journal of Science and Technology in Production and Manufacturing Engineering, Volume 3, Number 4, (2010), pp. 1-7. International Dr.K.Siva Prasad Mechanical Engineering 2010-2011


R.C. Chandra Mouli- (18)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Code Generation For Finite Element Analysis Of 2-D Heat Conduction Through Multi-Layers / Composites NCSAME (National Conference on “ State of the Art of Technologies in Mechanical Engineering), JNTUCE, Hyderabad,29th -30th June 2004. National Conference R.C. Chandra Mouli Mechanical Engineering 2004-2005
2 Finite Element Analysis of Static and Dynamic Strength of Tubular T-Joints Proceedings of the International Conference on Design and Advances in Mechanical Engineering,SKP Engg College, Tiruvannamalai,TN, 16th –17th Dec 2011. International Conference R.C. Chandra Mouli Mechanical Engineering 2011-2012
3 Effect of temperature and pressure ratio on second law efficiency of an endoreversible braysson cycle FIME-2010 (International Conference on ‘Frontiers in Mechanical engineering), NITK Surathkal, 20th -22nd May-2010. International Conference R.C. Chandra Mouli Mechanical Engineering 2009-2010
4 Modification of Base Frame of Bloom Pusher in Steel Plant INCRESE-2006 (International Conference on Reliability and Safety engineering), IIT Kharagpur, Kharagpur, 18th-20th December 2006. International Conference R.C. Chandra Mouli Mechanical Engineering 2006-2007
5 Code for Steady and Unsteady state 2D analysis on Composite Plate using Finite Element Technique ICCMS-2006 (International Conference on Computational Mechanics & Simulation), IIT Guwahati, Guwahati, 8th-10th December 2006. International Conference R.C. Chandra Mouli Mechanical Engineering 2006-2007
6 Mesh Generation for 2D Heat transfer and Fluid flow applications ICCMS-2006 (International Conference on Computational Mechanics & Simulation). IIT Guwahati, Guwahati, 8th-10th December 2006. International Conference R.C. Chandra Mouli Mechanical Engineering 2006-2007
7 Code Generation for Thermal Analysis of Pin Fins using Finite Element Technique CFEMATCON-2006 ( International Conference on Computational Fluid Dynamics, Acoustics Heat transfer and Electromagnetics), Andhra University, Visakhapatnam, 24th-25th July-2006. International Conference R.C. Chandra Mouli Mechanical Engineering 2006-2007
8 Development of Pre-Processor for CFD Analysis of 2D- Diffusers and Ducts ICASDA-2005 (International conference on advances in Structural dynamics and its applications)GITAM, Visakhapatnam,7th -9th December 2005. International Conference R.C. Chandra Mouli Mechanical Engineering 2005-2006
9 Alternative Thermal Insulators ICCES-2005 (International Conference on Computational & Experimental Engineering and Sciences), IIT Madras, 1st -6th December, 2005. International Conference R.C. Chandra Mouli Mechanical Engineering 2005-2006
10 Forgeability Aspects of Aluminium Alloys ICCES-2005 (International Conference on Computational & Experimental Engineering and Sciences), IIT Madras, 1st -6th December, 2005 International Conference R.C. Chandra Mouli Mechanical Engineering 2005-2006
11 Static strength analysis of a Tubular T-joint ICCMS – 2004 (International Conference on Computational Mechanics & Simulation), IIT Kanpur, 9th -12th December, 2004 International Conference R.C. Chandra Mouli Mechanical Engineering 2004-2005
12 Parametric and optimization studies of Reheat and Regenerative Braysson cycle Energy, An International Journal (Elsevier), Volume 93, Part-2, 2015. International Journal R.C. Chandra Mouli Mechanical Engineering 2015-2016
13 Energy and Exergy based Thermodynamic analysis of Reheat and Regenerative Braysson cycle Energy, An International Journal (Elsevier), Volume 90, Part-2, 2015 International Journal R.C. Chandra Mouli Mechanical Engineering 2015-2016
14 Second law analysis of an irreversible Braysson cycle International Journal of Exergy (Inderscienc), IJEX.Vol.6, No.6, 2009. International Journal R.C. Chandra Mouli Mechanical Engineering 2009-2010
15 Effect of angle-of-turn on the performance of divided intake ducts Proceedings of the institution of Mechanical Engineers, Proc.Instn Mech. Engrs Part G: J. Aerospace Engineering, Vol.218,2004. International Journal R.C. Chandra Mouli Mechanical Engineering 2004-2005
16 Performance Evaluation of Divided Intake Ducts: Effect of Area Ratio and Inlet Reynolds number International journal of Fluid Mechanics Research,Issue 5 International Journal of Fluid Mech Res. Vol.30,2003 International Conference R.C. Chandra Mouli Mechanical Engineering 2003-2004
17 Finite element analysis of elliptical cord tubular joints International journal of Manufacturing, materials and Mechanical Engineering-IJMME, Volume 3, Issue.2, 2013, pp.44-61 International R.C. Chandra Mouli Mechanical Engineering 2013-2014
18 Static Strength analysis of elliptical chord tubular T-Joints using FEA International Journal of Multidisciplinary Educational Research. (IJMER) ISBN: 2277-7881, Pages: 289-304 International R.C. Chandra Mouli Mechanical Engineering 2012-2013


M. Raja Roy- (19)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Studies On Tribological Properties Of Sic and Fly Ash Reinforced Glass Fiber Epoxy Composites By Taguchi Method, International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 6, November–December 2016, pp.199–208, Article ID: IJMET_07_0 International Journal M. Raja Roy Mechanical Engineering 2016-2017
2 Dry Sliding Wear Behavior Of Cr 3 c 2 -Nicr Coated Ti6al4v Implant Alloy Through Detonation Spray Method, International Journal of Mechanical Engineering and Technology (IJMET), Volume 7, Issue 6, November–December 2016, pp.378–387, Article ID: IJMET_07_0 International Journal M. Raja Roy Mechanical Engineering 2016-2017
3 Effect of Pitch angle on Bending Stresses of Bevel Gears International Advanced Research Journal in Science, Engineering and Technology, Vol. 3, Issue 11, ISSN (Online) 2393-8021 November 2016,Pg-140 - 145 International Journal M. Raja Roy Mechanical Engineering 2016-2017
4 Evaluation of % weight loss and Surface Roughness of Duplex Coated Ti6a14v Alloy using Taguchi Optimisation Techniquie International Journal of Engineering Trends and Technology (IJETT)- Volume 30 Number 6-December 2015 International Journal M. Raja Roy Mechanical Engineering 2015-2016
5 Position control of Stanford manipulator using artificial neural networks International Journal of Applied Sciences and Engineering Research, Vol. 4, Issue 4, June 2015 International Journal M. Raja Roy Mechanical Engineering 2015-2016
6 Static Analysis of Crane Hook with T-Section Using Ansys International Journal of Engineering Trends and Technology (IJETT) International Journal M. Raja Roy Mechanical Engineering 2015-2016
7 Stress Analysis of Crane Hook Using Fea 3rd International conference o Progress, Mechanical and Automobile Engineering, (ICMAE-2015), Goa, Feb 1st 2015 International Conference M. Raja Roy Mechanical Engineering 2014-2015
8 Stress Analysis of Crane Hook Using Fea international journal of current engineering and scientific research (ijcesr), ISSN (print): 2393-8374, volume-2, issue-2, 2015. International Journal M. Raja Roy Mechanical Engineering 2014-2015
9 Experimentation and Analysis of liquid Cooling System for Electronics Cooling International Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-17-23 International Journal M. Raja Roy Mechanical Engineering 2015-2016
10 Design and Fabrication of Mechatro Hand International Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-102-108 International Journal M. Raja Roy Mechanical Engineering 2015-2016
11 Evaluation of aMaterial Removal Rate and Surface Roughness in Turning Using Response Surface Methodology. Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-772-779 ISSN-2250-1758 International Journal M. Raja Roy Mechanical Engineering 2014-2015
12 Optimization of Machining Parameters for Cutting AMMC’s on Wire Cut EDM using RSM International Jouranl of Enigneering Trends and Technology (IJETT), Volume23 Number 2-May 2015,ISSN-2231-5381 International Journal M. Raja Roy Mechanical Engineering 2014-2015
13 Optimization of tool Temprature and Roughness in wet and dry Condition During Turning of Mid Steel Using Resopnse Surface Method International Jouranl of Enigneering Trends and Technology (IJETT), ISSN:2278-9359 Volume-4,Issue-5 International Journal M. Raja Roy Mechanical Engineering 2014-2015
14 Static and Thermal analysis of disc brake with Brake pad International Journal of Engineering Trends and Technology (IJETT), Volume 23 Number 8-May 2015 International Journal M. Raja Roy Mechanical Engineering 2014-2015
15 Design of Rack and Pinion Mechanism for Power Generation at speed Breakers Interanational Journal of Engineering Trends and Technology (IJETT), Volume-22,8th ,April-2015, ISSN Pg No-356-362 International Journal M. Raja Roy Mechanical Engineering 2014-2015
16 Modelling Simulation andf Kinematics Calucattions of Stanford Manipulator Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-136-141 International Journal M. Raja Roy Mechanical Engineering 2014-2015
17 Finite Element Analysis of Alloy Wheel Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-544-550 International Journal M. Raja Roy Mechanical Engineering 2014-2015
18 Effect of Cutting Parameters in Turning of Aluminium 2024 to Obtain Maximum MRR and Minimum Temprature by using RSM (Under Wet Condition) Interanational Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-51-58 International Journal M. Raja Roy Mechanical Engineering 2015-2016
19 Contact Pressure Analysis of Spur gear using FEA International Journal of Advanced Engineering Applications, Vol.7, Iss3, pp.27-41 International M. Raja Roy Mechanical Engineering 2013-2014


G.Uma Maheswara Rao- (2)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Static Analysis of 4-Blade Marine Propeller, Journal of Aerospace Engineering & Technology, 2015,Volume 5, Issue 2, pp. 8-21. International Journal G.Uma Maheswara Rao Mechanical Engineering 2015-2016
2 Finite Elements Analysis of Solid and Ventilated Disc Brake International Journal of Science and Research (IJSR), ISSN (online) :2319-7064 International Journal G.Uma Maheswara Rao Mechanical Engineering 2014-2015


M S S Srinivasa Rao- (7)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Design and Fabrication of a System to Reduce Motion Sickness International Journal of Engineering and Management Research, Volume-5,Issue-4,,August -15 Pg No-101-104 International Journal M S S Srinivasa Rao Mechanical Engineering 2015-2016
2 Energy and exergy based thermodynamics analysis of reheat and regenerative Braysson cycle Energy –ELSEVIER, Volume-90 (2015)Pg-1848-1858 International Journal M S S Srinivasa Rao Mechanical Engineering 2015-2016
3 Evaluation of % weight loss and Surface Roughness of Duplex Coated Ti6a14v Alloy using Taguchi Optimisation Techniquie International Journal of Engineering Trends and Technology (IJETT)- Volume 30 Number 6-December 2015 International Journal M S S Srinivasa Rao Mechanical Engineering 2015-2016
4 Stress analysis of 4stroke diesel engine Piston 3rd International Conference on Progress In Production,Mechanical And Automobile Engineering(ICPMAE 2015) International Conference M S S Srinivasa Rao Mechanical Engineering 2014-2015
5 Structural & Thermal Analyis of Gas Turbine Blade at Varying Operating Conditions International Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-24-28 International Journal M S S Srinivasa Rao Mechanical Engineering 2015-2016
6 Thermo-Structural Finite Element Analysis of I.C. Engine Pistons International Conference of International Colloquium on Materials, Manufacturing and Metrology, Organised by IIT Chennai, 8th Aug & 9th Aug-2014, pp 460-470 with ISBN 978-93-80689-18-0 International M S S Srinivasa Rao Mechanical Engineering 2014-2015
7 A study on Design and Analysis of Hybrid Vibration Damper with Energy Harvesting and Optimal Damping Effect Springer IE Journal Volume 95, Issue 2 pp 97-102 with DOI 10.100/s400-32-014-0115-3. International M S S Srinivasa Rao Mechanical Engineering 2014-2015


K. Naresh Kumar- (5)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Static and Thermal analysis of disc brake with Brake pad International Journal of Engineering Trends and Technology (IJETT), Volume 23 Number 8-May 2015 International Journal K. Naresh Kumar Mechanical Engineering 2014-2015
2 Prediction of surface roughness in Boring operation on mild steel using Taguchi approach Trends in Mechanical Engineering and Technology (2013) pages 29-34, ISSN: 2231-1793 International Journal K. Naresh Kumar Mechanical Engineering 2013-2014
3 Numerical Analysis of Centrifugal Blower Using CFD International Journal of Engineering Research & Technology ,Vol. 2 Issue 8, August 2013. International K. Naresh Kumar Mechanical Engineering 2013-2014
4 Effect of Bevel Angle and Wire Feed Rate in MIG Welding International Journal of Engineering Research & Technology ,Vol. 2 Issue 8, August 2013. International K. Naresh Kumar Mechanical Engineering 2013-2014
5 Experimental Investigation on Mechanical Properties of Coal Ash Reinforced Glass Fiber Polymer Matrix Composites International Journal of Emerging Technology and Advanced Engineering, Volume 3, Issue 8, August 2013. International K. Naresh Kumar Mechanical Engineering 2013-2014


D.Simhachalam - (7)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Design and Fabrication of a System to Reduce Motion Sickness International Journal of Engineering and Management Research, Volume-5,Issue-4,,August -15 Pg No-101-104 International Journal D.Simhachalam Mechanical Engineering 2015-2016
2 A review on Titanium Niobium Shape Memory Alloys (SMA) Journal of Material Science and Mechanical Engineering (JMSME),ISSN:2293-9095; Volume 2, Number 5; April-June,2015 pp.420-424 International Journal D.Simhachalam Mechanical Engineering 2015-2016
3 Finite Elements Analysis of Solid and Ventilated Disc Brake International Journal of Science and Research (IJSR), ISSN (online) :2319-7064 International Journal D.Simhachalam Mechanical Engineering 2014-2015
4 Prediction of surface roughness in Boring operation on mild steel using Taguchi approach Trends in Mechanical Engineering and Technology (2013) pages 29-34, ISSN: 2231-1793 International Journal D.Simhachalam Mechanical Engineering 2013-2014
5 Effect of SAW on weldability and mechanical properties of MS 2062 National Conference for Research on Latest innovations in Mechanical Engineering (LIM-2013) 28th April, 2013, pages163-166, ISBN 978-81-909853-4-5 National Conference D.Simhachalam Mechanical Engineering 2013-2014
6 Effect of ageing on Mechanical Properties of dissimilar friction stir welded aluminum alloy (AA2024 & AA6351) joints International Conference on Intelligent Manufacturing Systems ( ICIMS-2012) held at Sastra University Tanjavur, Tamilnadu. International Conference D.Simhachalam Mechanical Engineering 2012-2013
7 Effect of ageing on Mechanical Properties of dissimilar friction stir welded aluminum alloy (AA2024 & AA6351) joints Journal of Applied Sciences, 12: 1053-1057. International Journal D.Simhachalam Mechanical Engineering 2012-2013


K.Satya Narayana - (15)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Diagnostic Approach Through Condition Based Monotoring in Motor Rotor Using Vibration Signature Analysis National Conference on Condition Monotoring , 2015. National Conference K.Satya Narayana Mechanical Engineering 2015-2016
2 Condition Monotoring and Detection of Unbalance Using Vibration Signature Analysis International Journal of Recent Scientific Research , Vol.6, Issue,8,pp.5796-5800.August,2015. International Journal K.Satya Narayana Mechanical Engineering 2015-2016
3 Variable Compression Ration Diesel Engine Performance Analysis Engineering Technology Trends and Technology (IJETT), Number, 01, October 2015 International Journal K.Satya Narayana Mechanical Engineering 2015-2016
4 Stress analysis of 4stroke diesel engine Piston 3rd International Conference on Progress In Production,Mechanical And Automobile Engineering(ICPMAE 2015) ISBN: 978-93-85225-02-4,1st February, 2015, International Conference K.Satya Narayana Mechanical Engineering 2014-2015
5 Performance characteristics of variable compression ratio diesel engine Internation Conferecnce on Advances in engineering Reseasrch International Conference K.Satya Narayana Mechanical Engineering 2015-2016
6 Stress Analysis of Crane Hook Using Fea 3rd International conference o Progress, Mechanical and Automobile Engineering, (ICMAE-2015), Goa, Feb 1st 2015 International Conference K.Satya Narayana Mechanical Engineering 2014-2015
7 Stress Analysis of Crane Hook Using Fea international journal of current engineering and scientific research (ijcesr), ISSN (print): 2393-8374, volume-2, issue-2, 2015. International Journal K.Satya Narayana Mechanical Engineering 2014-2015
8 Finite Elements Analysis of Solid and Ventilated Disc Brake International Journal of Science and Research (IJSR), ISSN (online) :2319-7064 International Journal K.Satya Narayana Mechanical Engineering 2014-2015
9 Finite element analysis of elliptical cord tubular joints International journal of Manufacturing, materials and Mechanical Engineering-IJMME, Volume 3, Issue.2, 2013, pp.44-61 International K.Satya Narayana Mechanical Engineering 2013-2014
10 Thermo-Structural Finite Element Analysis of I.C. Engine Pistons International Conference of International Colloquium on Materials, Manufacturing and Metrology, Organised by IIT Chennai, 8th Aug & 9th Aug-2014, pp 460-470 with ISBN 978-93-80689-18-0 International Conference K.Satya Narayana Mechanical Engineering 2014-2015
11 A study on Design and Analysis of Hybrid Vibration Damper with Energy Harvesting and Optimal Damping Effect Springer IE Journal Volume 95, Issue 2 pp 97-102 with DOI 10.100/s400-32-014-0115-3. International Journal K.Satya Narayana Mechanical Engineering 2013-2014
12 Finite element analysis of static and dynamic strength of tubular T-Joints International Conference on Design and Advances in Mechanical Engineering (ICDAAME2011), 16-17 December, 2011. Pp.58-64 International Conference K.Satya Narayana Mechanical Engineering 2011-2012
13 Static Strength analysis of elliptical chord tubular T-Joints using FEA International Journal of Multidisciplinary Educational Research. (IJMER) ISBN: 2277-7881, Pages: 289-304 International Journal K.Satya Narayana Mechanical Engineering 2012-2013
14 Finite Element Analysis of Static and Dynamic Strength of circular and Elliptical Tubular T-Joints India institute of technology, Delhi at ACMFMS a International Conference, on Dec 5th-8th 2012. International Conference K.Satya Narayana Mechanical Engineering 2012-2013
15 Static strength analysis of Tubulur T-Joints using Ansys Journal of Basic and Applied scientific research, 1(9) 989-997,2011 International Journal K.Satya Narayana Mechanical Engineering 2011-2012


D.S.S. Sai Ravi kiran- (4)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Contact Pressure Analysis of Spur gear using FEA International Journal of Advanced Engineering Applications, Vol.7, Iss3, pp.27-41 International D.S.S. Sai Ravi kiran Mechanical Engineering 2013-2014
2 MULTI OBJECTIVE OPTIMIZATION OF TOOL LIFE AND TOTAL COST USING 3-LEVEL FULL FACTORIAL METHOD IN CNC END MILLING PROCESS 2013 July - I.J.E.M.R.R - International Journal , ISSN 2278 - 0149, Volume - 2. International D.S.S. Sai Ravi kiran Mechanical Engineering
3 Prediction of Surface Roughness Using Response Surface Methodology on Al-6061 alloy 2012 May - National Welding Seminar - National Journal National D.S.S. Sai Ravi kiran Mechanical Engineering
4 PC Based Automation of Low Cost CNC Plasma Profile Cutting Pipes National Welding Conference National D.S.S. Sai Ravi kiran Mechanical Engineering


K.V. Rukmini- (3)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Economic Design Of x Bar Control Charts Considering Process Shift Distributions. Journal Of Industrial Engineering International - A Springer Open Journal, Vol 10, ISSUEN0.4, Dec -2014 ,pp163-171,ISSN Online: 2251-712X (electronic version International Journal K.V. Rukmini Mechanical Engineering 2014-2015
2 Economic Design of X bar Control Chart Using Differential Evolution International Journal of Emerging Technology and Advanced Engineering, ISSN: 2250-2459 (Online), Volume 3, Issue 4, April 2013, Pages 541-548. International K.V. Rukmini Mechanical Engineering 2012-2013
3 Economic Design of Joint X bar and R Control Charts Using Differential Evolution International Journal (Jordan Journal of Mechanical and Industrial Engineering, ISSN: 1995-6665, Volume 5, Number 2, April 2011, Pages 149-160). International K.V. Rukmini Mechanical Engineering 2010-2011


M. Prasanth Kumar - (9)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Study on Stress Analysis of Araldite HY-951 and CY-230 Bell Crank Lever using Photoelasticity and FEM Journal of Automobile Engineering and Applications, Volume 4, Issue 2,pp.10-21. International Journal M. Prasanth Kumar Mechanical Engineering 2017-2018
2 A review on Titanium Niobium Shape Memory Alloys (SMA) Journal of Material Science and Mechanical Engineering (JMSME),ISSN:2293-9095; Volume 2, Number 5; April-June,2015 pp.420-424 International Journal M. Prasanth Kumar Mechanical Engineering 2015-2016
3 Design and Experimental Study of Small-Scale Fabricated Thermo-Acoustic Refrigerator International Journal of Engineering Trends and Technology (IJETT) in Sep 2013 volume 4 issue 9. ISSN: 2231-5381. International M. Prasanth Kumar Mechanical Engineering 2013-2014
4 Numerical Analysis of Centrifugal Blower Using CFD International Journal of Engineering Research & Technology ,Vol. 2 Issue 8, August – 2013. International M. Prasanth Kumar Mechanical Engineering
5 Effect of Bevel Angle and Wire Feed Rate in MIG Welding International Journal of Engineering Research & Technology ,Vol. 2 Issue 8, August – 2013. International M. Prasanth Kumar Mechanical Engineering
6 Experimental Investigation on Mechanical Properties of Coal Ash Reinforced Glass Fiber Polymer Matrix Composites International Journal of Emerging Technology and Advanced Engineering, Volume 3, Issue 8, August 2013. International M. Prasanth Kumar Mechanical Engineering
7 Effect of SAW on weldability and mechanical properties of MS 2062 National Conference for Research on Latest innovations in Mechanical Engineering (LIM-2013) 28th April, 2013, pages163-166, ISBN 978-81-909853-4-5 National M. Prasanth Kumar Mechanical Engineering
8 FRICTION STIR WELDING OF ALUMINIUM ALLOYS (AA6351 AND AA2024) National Welding Seminar (NWS) by IIW held at Kolkata on 10,11,12 December 2009. Page 68 National M. Prasanth Kumar Mechanical Engineering
9 Static Strength analysis of elliptical chord tubular T-Joints using FEA International Journal of Multidisciplinary Educational Research. (IJMER) ISBN: 2277-7881, Pages: 289-304 International M. Prasanth Kumar Mechanical Engineering


P.Ramya - (2)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Evaluation of % weight loss and Surface Roughness of Duplex Coated Ti6a14v Alloy using Taguchi Optimisation Techniquie International Journal of Engineering Trends and Technology (IJETT)- Volume 30 Number 6-December 2015 International Journal P.Ramya Mechanical Engineering 2015-2016
2 Analysis of Flow over Passenger Cars using Comutational Fluid Daynamics International Journal of Engineering Trends and Technology (IJETT)- Volume 29 Number 4-November 2015 International Journal P.Ramya Mechanical Engineering 2015-2016


V. Bindu Niharika - (2)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 An Integrative perspective of TQM and performance appraisal Indo American Journal of Mechanical Engineering (IJETT) National V. Bindu Niharika Mechanical Engineering 2013-2014
2 Minimization of wastage of material for a flat production using different heuristics International Journal of Engineering Trends and Technology (IJETT) in Aug 2013 volume 4 issue 8. ISSN: 2231-5381. International V. Bindu Niharika Mechanical Engineering 2013-2014


S. Phani Kumar - (11)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Position control of Stanford manipulator using artificial neural networks International Journal of Applied Sciences and Engineering Research, Vol. 4, Issue 4, June 2015 International Journal S. Phani Kumar Mechanical Engineering 2015-2016
2 Design and Fabrication of Mechatro Hand International Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-102-108 International Journal S. Phani Kumar Mechanical Engineering 2015-2016
3 Design of Rack and Pinion Mechanism for Power Generation at speed Breakers Interanational Journal of Engineering Trends and Technology (IJETT), Volume-22,8th, April-2015, ISSN Pg No-356-362 International Journal S. Phani Kumar Mechanical Engineering 2014-2015
4 Modelling Simulation andf Kinematics Calucattions of Stanford Manipulator Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-136-141 International Journal S. Phani Kumar Mechanical Engineering 2014-2015
5 Finite Element Analysis of Alloy Wheel Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-544-550 International Journal S. Phani Kumar Mechanical Engineering 2014-2015
6 Design and Modelling of Agricultural Sprayer International Journal of Engineering Trends and Technology (IJETT) Volume 23 Number 6- May 2015, ISSN: 2231-5381, pp 308-316 International Journal S. Phani Kumar Mechanical Engineering 2015-2016
7 Effect of Cutting Parameters in Turning of Aluminium 2024 to Obtain Maximum MRR and Minimum Temprature by using RSM (Under Wet Condition) Interanational Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-51-58 International Journal S. Phani Kumar Mechanical Engineering 2015-2016
8 Thermo-Structural Finite Element Analysis of I.C. Engine Pistons International Conference of International Colloquium on Materials, Manufacturing and Metrology, Organised by IIT Chennai, 8th Aug & 9th Aug-2014, pp 460-470 with ISBN 978-93-80689-18-0 International S. Phani Kumar Mechanical Engineering 2014-2015
9 Contact Pressure Analysis of Spur gear using FEA International Journal of Advanced Engineering Applications, Vol.7, Iss3, pp.27-41 International S. Phani Kumar Mechanical Engineering 2013-2014
10 MULTI OBJECTIVE OPTIMIZATION OF TOOL LIFE AND TOTAL COST USING 3-LEVEL FULL FACTORIAL METHOD IN CNC END MILLING PROCESS 2013 July - I.J.E.M.R.R - International Journal International S. Phani Kumar Mechanical Engineering 2013-2014
11 Selection of optimal lighting conditions for surface texture measurement on inclined machined surfaces International Journal of Advanced Engineering Applications, Vol.6, Iss1, pp.8-16 International S. Phani Kumar Mechanical Engineering 2012-2013


S. Kakati - (3)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 An Integrative perspective of TQM and performance appraisal Indo American Journal of Mechanical Engineering (IJETT) National S. Kakati Mechanical Engineering
2 Minimization of wastage of material for a flat production using different heuristics International Journal of Engineering Trends and Technology (IJETT) in Aug 2013 volume 4 issue 8. ISSN: 2231-5381. International S. Kakati Mechanical Engineering
3 Evaluation of chip breaker using flank wear on EN-8 steel and optimization of machining parameters for maximum tool life and minimum chip length using RSM methodology International Journal of Engineering Research and Development e-ISSN: 2278-067x, p-ISSN: 2278-800X, Volume 7, Issue 2 (May 2013), PP. 12-20 International S. Kakati Mechanical Engineering


V. Krishna - (8)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Optimization of Shell and Tube Heat Exchangers Using ANT Colony Prin Ciples Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-415-419 ISSN-2250-0758 International Journal V. Krishna Mechanical Engineering 2014-2015
2 Analysis of Tensile and Creep Data of 316L (N) Stainless Steel International Conference from 6th Jan to 8th Jan2013 at Vellore. International Conference V. Krishna Mechanical Engineering 2012-2013
3 Aerofoil Profile Analysis and Design Opimisation Journal of Aerospace Engineering and Technologyť Volume 3, Issue.2, 2013, pp.1-10. National V. Krishna Mechanical Engineering 2013-2014
4 Numerical Analysis of Centrifugal Blower Using CFD International Journal of Engineering Research & Technology ,Vol. 2 Issue 8, August 2013. International V. Krishna Mechanical Engineering 2013-2014
5 Effect of Bevel Angle and Wire Feed Rate in MIG Welding International Journal of Engineering Research & Technology ,Vol. 2 Issue 8, August 2013. International V. Krishna Mechanical Engineering 2013-2014
6 Experimental Investigation on Mechanical Properties of Coal Ash Reinforced Glass Fiber Polymer Matrix Composites International Journal of Emerging Technology and Advanced Engineering, Volume 3, Issue 8, August 2013. International V. Krishna Mechanical Engineering 2013-2014
7 Aero\Dynamic & Aerocoustic Analysis of Centrifugal Blower for Noise Reduction National Symposium on Acoustics. National V. Krishna Mechanical Engineering 2012-2013
8 Finite Element Analysis of Static and Dynamic Strength of circular and Elliptical Tubular T-Joints India institute of technology, Delhi at ACMFMS a Interational Conference, on Dec 5th-8th 2012. International V. Krishna Mechanical Engineering 2011-2012


Y.L. Vidya - (2)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 An Integrative perspective of TQM and performance appraisal Indo American Journal of Mechanical Engineering (IJETT) National Y.L. Vidya Mechanical Engineering
2 Minimization of wastage of material for a flat production using different heuristics International Journal of Engineering Trends and Technology (IJETT) in Aug 2013 Volume 4 issue 8. ISSN: 2231-5381 International Y.L. Vidya Mechanical Engineering


B. Ananda Rao - (1)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Design and Experimental Study of Small-Scale Fabricated Thermo-Acoustic Refrigerator International Journal of Engineering Trends and Technology (IJETT) in Sep 2013 volume 4 issue 9. ISSN: 2231-5381. International B. Ananda Rao Mechanical Engineering 2013-2014


D. Srinivasa Rao - (5)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Interanation Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-415-419 ISSN-2250-0758 Optimization of Shell and Tube Heat Exchangers Using ANT Colony Prin Ciples International Journal D. Srinivasa Rao Mechanical Engineering 2014-2015
2 Finite Element Modelling of TIG Welding for 316L Stainless Steel Plate using Sysweld Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-390-397 ISSN-2250-0758 International Journal D. Srinivasa Rao Mechanical Engineering 2014-2015
3 Welding Development in ESR Modified 15CDV6 Material International Journal of Mechanical Engineering and Robotics Research (IJMERR) International Journal D. Srinivasa Rao Mechanical Engineering 2014-2015
4 Effect Of Nano Rubber Additions On Wear And Mechanical Properties Of Epoxy Glass Fibre Composites IJETR, Volume V1, Issue I4 May - June, 2014 International Journal D. Srinivasa Rao Mechanical Engineering 2014-2015
5 Design and Experimental Study of Small-Scale Fabricated Thermo-Acoustic Refrigerator International Journal of Engineering Trends and Technology (IJETT) in Sep 2013 volume 4 issue 9. ISSN: 2231-5381. International D. Srinivasa Rao Mechanical Engineering 2013-2014


B.B. Ashok Kumar - (1)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Prediction of surface roughness in Boring operation on mild steel using Taguchi approach Trends in Mechanical Engineering and Technology (2013) pages 29-34, ISSN: 2231-1793 National B.B. Ashok Kumar Mechanical Engineering 2013-2014


M. Chandra Sekhar - (4)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Study on Stress Analysis of Araldite HY-951 and CY-230 Bell Crank Lever using Photoelasticity and FEM Journal of Automobile Engineering and Applications, Volume 4, Issue 2,pp.10-21. International Journal M. Chandra Sekhar Mechanical Engineering 2017-2018
2 Condition Monotoring and Detection of Unbalance Using Vibration Signature Analysis International Journal of Recent Scientific Research , Vol.6, Issue,8,pp.5796-5800.August,2015. International Journal M. Chandra Sekhar Mechanical Engineering 2015-2016
3 Evaluation of Mechanical properties of Aluiminium alloy (AA 6061) Reinforced with molybdenum International Conference on Advances in Design & Manufactuirng (Icad&M’14) (ICAD&M’14) Dec 5th-7th,2014. International Conference M. Chandra Sekhar Mechanical Engineering 2014-2015
4 Welding Development in ESR Modified 15CDV6 Material International Journal of Mechanical Engineering and Robotics Research (IJMERR) International Journal M. Chandra Sekhar Mechanical Engineering 2014-2015


M. Amareswari Reddy - (6)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Static Analysis of Crane Hook with I-Section using Ansys International Journal of Engineering and Management Research, Volume-5, Issue-3, June 2015. International Journal M. Amareswari Reddy Mechanical Engineering 2015-2016
2 Static Analysis of Crane Hook with I-Section and T-Section using Ansys International Journal of Engineering Trends and Technology, Volume 26 number 2-August 2015. International Journal M. Amareswari Reddy Mechanical Engineering 2015-2016
3 Conceptual Design of Cycle Frame International Journal of Engineering Trends and Technology, Volume 38 number 2- August 2016. International Journal M. Amareswari Reddy Mechanical Engineering 2016-2017
4 Modelling and Analysis of Double Girder Gantry Crane International Journal of Engineering and Management Research, Volume-6, Issue-4 of July-August 2016. International Journal M. Amareswari Reddy Mechanical Engineering 2016-2017
5 Static Analysis of Crane Hook with T-Section Using Ansys International Journal of Engineering Trends and Technology (IJETT) International Journal M. Amareswari Reddy Mechanical Engineering 2015-2016
6 Finite Element Modelling of TIG Welding for 316L Stainless Steel Plate using Sysweld Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-390-397 ISSN-2250-0758 International Journal M. Amareswari Reddy Mechanical Engineering 2014-2015


M.N.V. Krishna Veni - (8)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 A Parametric Study On Design Of Helmet To Mitigate Brain Damage And To Optimize The Weight International Journal of ARPN Journal of Engineering and Applied Sciences, Volume-10, number 6, April 2015. International Journal M.N.V. Krishna Veni Mechanical Engineering 2015-2016
2 Static Analysis of Crane Hook with I-Section and T-Section using Ansys International Journal of Engineering Trends and Technology, Volume 26 number 2-August 2015. International Journal M.N.V. Krishna Veni Mechanical Engineering 2015-2016
3 Conceptual Design of Cycle Frame International Journal of Engineering Trends and Technology, Volume 38 number 2- August 2016. International Journal M.N.V. Krishna Veni Mechanical Engineering 2016-2017
4 Modelling and Analysis of Double Girder Gantry Crane International Journal of Engineering and Management Research, Volume-6, Issue-4 of July-August 2016. International Journal M.N.V. Krishna Veni Mechanical Engineering 2016-2017
5 Diagnostic Approach Through Condition Based Monotoring in Motor Rotor Using Vibration Signature Analysis National Conference on Condition Monotoring , 2015. National Conference M.N.V. Krishna Veni Mechanical Engineering 2015-2016
6 Static Analysis of Crane Hook with T-Section Using Ansys International Journal of Engineering Trends and Technology (IJETT) International Journal M.N.V. Krishna Veni Mechanical Engineering 2015-2016
7 A Parametric study on design of helmet to mitigate brain damage and to optimize the weight ARPN Journal of Engineering and Applied Sciences, Vol 10,NO.6,April 2015,ISSN1819-6608, International Journal M.N.V. Krishna Veni Mechanical Engineering 2014-2015
8 Finite Element Modelling of TIG Welding for 316L Stainless Steel Plate using Sysweld Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-390-397 ISSN-2250-0758 International Journal M.N.V. Krishna Veni Mechanical Engineering 2014-2015


M. Sailaja - (10)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Condition Monitoring and Fatigue Life Analysis of Internal Combustion Engine Connecting Rod International Conference in GITAM University, under CMSI International Conference M. Sailaja Mechanical Engineering 2016-2017
2 Investigations on Effect of Cutting Forces and Surface Finish in Plain Milling Using Box Behnke Design Journal of Thin Films, Coating Science Technology and Application , page No 17-30, Volume 3, Issue 1 International Journal M. Sailaja Mechanical Engineering 2016-2017
3 Diagnostic Approach Through Condition Based Monotoring in Motor Rotor Using Vibration Signature Analysis National Conference on Condition Monotoring , 2015. National Conference M. Sailaja Mechanical Engineering 2015-2016
4 Condition Monotoring and Detection of Unbalance Using Vibration Signature Analysis International Journal of Recent Scientific Research , Vol.6, Issue,8,pp.5796-5800.August,2015. International Journal M. Sailaja Mechanical Engineering 2015-2016
5 Design and Fabrication of a System to Reduce Motion Sickness International Journal of Engineering and Management Research, Volume-5,Issue-4,,August -15 Pg No-101-104 International Journal M. Sailaja Mechanical Engineering 2015-2016
6 Study on Effect of Plain Milling parameters on Cutting Forces and Surface Finish Using Statistical Approach Journal of Advance in Mechanical Engineering and Technology, Volume 1, Issue 1, pp.22-34,2015 International Journal M. Sailaja Mechanical Engineering 2015-2016
7 Position control of Stanford manipulator using artificial neural networks International Journal of Applied Sciences and Engineering Research, Vol. 4, Issue 4, June 2015 International Journal M. Sailaja Mechanical Engineering 2015-2016
8 Design of Rack and Pinion Mechanism for Power Generation at speed Breakers Interanation Journal of Engineering Trends and Technology (IJETT), Volume-22,8th ,April-2015, ISSN Pg No-356-362 International Journal M. Sailaja Mechanical Engineering 2014-2015
9 Modelling Simulation andf Kinematics Calucattions of Stanford Manipulator Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-136-141 International Journal M. Sailaja Mechanical Engineering 2014-2015
10 Finite Element Analysis of Alloy Wheel Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-544-550 International Journal M. Sailaja Mechanical Engineering 2014-2015


P. Chandra Sekhar - (1)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Experimentation and Analysis of liquid Cooling System for Electronics Cooling Internation Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-17-23 International Journal P. Chandra Sekhar Mechanical Engineering 2015-2016


B.V. Ravi Teja - (2)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Back Propagation Neural Networks for the Analysis of Control Chart Pattern Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-602-605 International Journal B.V. Ravi Teja Mechanical Engineering 2014-2015
2 Structural & Thermal Analyis of Gas Turbine Blade at Varying Operating Conditions International Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-24-28 International Journal B.V. Ravi Teja Mechanical Engineering 2015-2016


B. Pradeep Kumar - (4)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Back Propagation Neural Networks for the Analysis of Control Chart Pattern Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-602-605 International Journal B. Pradeep Kumar Mechanical Engineering 2014-2015
2 Effect of Cutting Parameters in Turning of Aluminium 2024 to Obtain Maximum MRR and Minimum Temprature by using RSM (Under Wet Condition) Interanational Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-51-58 International Journal B. Pradeep Kumar Mechanical Engineering 2015-2016
3 Effect of Cutting Parameters in Turning of Aluminium 2024 to Obtain Maximum MRR and Minimum Temprature by using RSM (Under Dry Condition) Interanational Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-94-101 International Journal B. Pradeep Kumar Mechanical Engineering 2015-2016
4 Design and Modelling of Agricultural Sprayer International Journal of Engineering Trends and Technology (IJETT) Volume 23 Number 6- May 2015, ISSN: 2231-5381, pp 308-316 International Journal B. Pradeep Kumar Mechanical Engineering 2015-2016


J.V. Bhanu Tej - (2)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Design and Modelling of Agricultural Sprayer International Journal of Engineering Trends and Technology (IJETT) Volume 23 Number 6- May 2015, ISSN: 2231-5381, pp 308-316 International Journal J.V. Bhanu Tej Mechanical Engineering 2015-2016
2 Effect of Cutting Parameters in Turning of Aluminium 2024 to Obtain Maximum MRR and Minimum Temprature by using RSM (Under Dry Condition) Interanational Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-94-101 International Journal J.V. Bhanu Tej Mechanical Engineering 2015-2016


V.V. Narayana Reddy - (2)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Optimization of Shell and Tube Heat Exchangers Using ANT Colony Prin Ciples Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-415-419 ISSN-2250-0758 International Journal V.V. Narayana Reddy Mechanical Engineering 2014-2015
2 Finite Element Modelling of TIG Welding for 316L Stainless Steel Plate using Sysweld Interanational Journal of Engineering and Management Research, Volume-5,Issue-2,April-2015, Pg No-390-397 ISSN-2250-0758 International Journal V.V. Narayana Reddy Mechanical Engineering 2014-2015


R.D.V. Prasad - (2)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Design and Fabrication of a System to Reduce Motion Sickness International Journal of Engineering and Management Research, Volume-5,Issue-4,,August -15 Pg No-101-104 International Journal R.D.V. Prasad Mechanical Engineering 2015-2016
2 Structural & Thermal Analyis of Gas Turbine Blade at Varying Operating Conditions International Journal of Engineering and Management Research, Volume-5,Issue-3,June-2015, Pg-24-28 International Journal R.D.V. Prasad Mechanical Engineering 2015-2016


G Naresh - (4)


S.No Title Conference/Journal Name category Staff Name Department Academic Year
1 Fabrication and Characterization of Al356.2, Rice Husk Ash and Fly Ash Reinforced Hybrid Metal Matrix Composite International Journal of Advanced Science and Technology, Vol.94 (2016), pp.49-56, ISSN: 2005-4238 IJAST International Journal G Naresh Mechanical Engineering 2016-2017
2 Thermo-Structural Analysis of I.C. Engine Piston Journal of Automobile Engineering and Application, ISSN: 2455-3360(online),Volume 3, Issue 2, JoAEA(2016) 37-44 © STM Journals 2016. International Journal G Naresh Mechanical Engineering 2016-2017
3 Optimization of Machining Parameters In Milling of AA 64430 with Its AMC” International Journal of Mechanical Engineering & Computer Applications IJMCA, Vol. 4, No. 3, May- June , 2016, ISSN - 2320-6349. International Journal G Naresh Mechanical Engineering 2016-2017
4 An Investigation of Transient Thermal Analysis of 1st Stage Gas Turbine Blade Manufactured by Directional Solidification and Mechanically Alloyed Nickel-Based Superalloys International Journal of Advanced Science and Technology Vol.85 (2015), ISSN: 2005-4238 IJAST, pp.17-28. International Journal G Naresh Mechanical Engineering 2015-2016